| Type: | Fiber Alignment |
|---|---|
| Condition: | New |
| Model: | Hu125-Sm (Single-Mode Optical Fiber 9/125 Um) Hu12 |
| Customization: |
|---|
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
| Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
Suppliers with verified business licenses
Audited Supplier
It is applicable to SM or MM fiber and can be connected easily and quickly under any
circumstances. Most importantly, its insertion loss is below 0.3dB.
Under the premise of Time is Money, the outstanding features of HU125 can provide a rapid
and accurate measurement and research on fibers various optical properties. For example,
the connection of O.T.D.R., Optical Spectrum Analyzers, Light Source, Power Meter and
Fiber phone (for communication during the execution of fiber cable engineering), etc.
Application: R&D, Factory, Outdoor engineering, repair and maintenance.
(2) Specifications
1. Model: HU125-SM (single-mode optical fiber 9/125 um) FC connector (other connector need to mention before payment. )
HU125-MM (multi-mode optical fiber 50/125 um or 62.5/125 um)
2. Pigtail length: 150?5cm
3. Insertion Loss: < 0.3 dB
4. Number of insertions: 10,000 min.
5. Reflection Loss: < - 50 dB typ.
6. Alignment Time: < 1 second
7. Matching Oil: Index of refraction(ND) ?1.4500 +/- 0.01(not offer ,can be replaced by 75 degree alcohol )
(Alcohol or pure water or distilled water containing at least 30% alcohol can also beused.)
8. Connector types: FC,SC,ST,D4,E2000,LC,DIN
9. Operating Temperature: 14° to 122° F (-10° to +50° C)
10. Storage Temperature: -40° to 140° F (-40° to +60° C)
(3) Operation
1. Connect the connector to the unit on the instrument to be tested under light source (for
example, O.T.D.R.)
2. First, scrub the end of HU125 for alignment repeatedly with a cleaning brush moistened
by alcohol in the direction indicated by the arrow above the slot. Then clean the slot
and the fiber input port with an air cleaner several times, and drop a little matching oil.
3. After cleaning the bare fiber with alcohol, cut the fiber by following the standard cutting
process (or cut it with the scissors or just break it by your hand. * Note 1). The
length of the bare fiber is about 12 mm as shown in the following drawing. Then insert
the fiber into the fiber input port of HU125 lightly and entirely for test.
* Note 1: If the optical fiber is cut by the scissors or by hand, then only the matching oil with
an index of refraction (ND) ?1.4500 +/- 0.01 can be used as a medium. Alcohol or pure
water containing at least 30% alcohol is not suitable for such cutting method.
(4) Maintenance (** Note: Do not use acetone in any case.)
If the fiber becomes opaque, please take the following steps:
1. Draw out the bare fiber in the alignment end of the HU125, and then repeat the steps
described in (3)-2 until the fiber becomes transmittal.
2. If HU125 is used in an adverse circumstance (such as the outdoor work site for
installation of optical fiber), then the inner part of the HU125 will be stained with some
gelatinous impurities and thus lead to opaque. At this moment, it is suggested to clean the HU125 in an ultrasonic cleaner for about 5 minutes as shown in the following drawing. (Alcohol can be used in the ultrasonic cleaner as cleaning agent.) After that, repeat the cleaning steps of (3)-2.
3. Should the bare fiber break, there will be two methods for troubleshooting:
a. If the bare fiber breaks at the position as indicated in Fig. (a), the cleaning wire can
be used to remove the broken fiber completely in a manner shown in Fig. (b) and
(c).
b. If the bare fiber breaks at the position as indicated in Fig. (d), then a needle can be
put in the center of the slot as shown in Fig. (e) at the edge of the bare fiber. Press
the needle gently to squeeze the bare fiber out easily. At this time, break the fiber
and then eliminate the residual fiber in the slot in the way indicated in Fig (f).
4. Fabrication of Cleaning Wire
Properly heat the cotton stick at the central position and then stretch it to be a tubular shape as shown in the following drawing. Cut it into two pieces and put them into the steel threads respectively. Then fix them to the threads with super glue.
(5) Package Includes
1. HU125 Fiber Pigtail
2. Manual
3. Index Matching Oil
4. Cleaning Brush
5. Needle
6. Cleaning Wire (put in the needle)
| 1 | Fusion Splicers | Chinese fusion splicer/Japanese fusion splicer/Korea fusion splicer/ |
| 2 | OTDR | Chinese OTDR/USA OTDR/ Canada OTDR/Japanese OTDR/CWDM OTDR/DWDM OTDR/CWDM OTDR |
| 3 | Test instruments | optical power meters/optical laser sources/visual fault locators / PON power meters / |
| Fiber Optical Multimeter/Optical Attenuator/Optical talk sets/cable fault locators/Fiber Identifier | ||
| 4 | Fiber Tools | Fiber cleaver/Fiber stripper/Cable sheath slitter/ kevlar scissors/Fiber cleaning tools/ |
| Loose Tube Stripping Tool/Fiber optic termination kit/bare fiber connector/V-groove/launch Cable/ | ||
| Bare Fiber Alignment device/Cable jointing tool kit/ FTTH tools kit/ | ||
| Thermal Stripper | ||
| 5 | Wireless Test Equipment | Sitemaster/ Spectrum Analyzer |
| 6 | Data Test Instrument | E1 Error Bit Tester/Ethernet Tester |
| 7 | Battery Tester | Battery internal resistance tester |
| 8 | Accessories | Patch Cord/ fiber Adapter/Fiber Cable/Fusion splcier Battery/ |
| OTDR battery/Electorde/Blade/Power changer |
1. Beijing W&F technology Co.,LTD was founded in 2006.which located in Beijing- the capital of China. More than 15 years professional experience in fiber optic euqipments field makes us pay more attention to the quality.
2. Our brand ONEFIND are selling all over the world.
3. Life long technical support, quick feedback to any problem.
4. We can also provide OEM service.
5. "Satisfaction of the clients is service standard" --is our marketing service strate.
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}